Weather and lift in Thermiker
Thermiker simulates a soaring day from morning to evening. Thermals are columns of 160 to 330 m radius with a core of 1.0 to 3.6 m/s at the peak of the day. Each lives 15 to 30 minutes, drifts and leans with the wind, is ringed by sink and marked by a cumulus. Wind on a slope gives ridge lift, strong wind across a range gives lee waves with rotor, and the sun drives slope and valley winds. Five kinds of day run from blue to wave, and you set wind, cloud base and thermal strength. There is no rain and no storm.
What you can set
- Kind of day: Classic cumulus day, Strong day, Blue day, Weak day or Wave day. Each sets strength, cloud base and thermal count, and you can change them after.
- Wind speed (up to 70 km/h) and direction.
- Thermal strength, 25 % to 200 %.
- Cloud base, from 1,400 m up to the top for the region.
- Turbulence: off, normal or rough.
- Start time, 09:00 to 18:00. The clock runs with the flight, and time acceleration speeds up the day.
Every new flight starts with a fresh set of thermals. The daily final glide gives every pilot the same start, wind and thermal strength for that date.
Thermals
- Size and strength. Radius 160 to 330 m. Peak core 1.0 to 3.6 m/s, with more weak thermals than strong ones. The day factor and the Thermal strength setting scale it.
- Shape. Lift falls off gently inside the thermal, so centring pays, and drops steeply at the edge. Across the starter thermal at 95 km/h you feel a surge of about 0.1 g.
- Life cycle. A thermal builds over the first 20 % of its life and decays over the last 25 %. Then it is gone until the day needs another.
- Bubbles. Warm bubbles rise through the column at about 3 m/s, 300 to 800 m apart. The lift swings by 25 % around its mean.
- Height. Lift is weak near the ground, strongest in the middle of the layer and fades over the top 15 %.
- Climb. A 15 m glider circling at 40 degrees of bank at 95 km/h climbs 1.13 m/s with the circle centred, 0.96 m/s with it 100 m off and 0.26 m/s 200 m off.
- Spacing. In all the real regions thermals stand 1.5 times the depth of the convective layer apart, which is what aircraft measurements give. A layer 2,000 m deep gives a thermal about every 3 km. How thermals work.
Drift, lean and wind near the ground
A thermal drifts with the wind. It also leans downwind with height, about 0.6 m per metre of height in 20 km/h of wind, so the core at your height sits downwind of where it left the ground. Near the ground the wind fades over the lowest 100 m. That is why the crab angle at touchdown stays small.
Sink
Sink rings sit around every thermal: a thin ring at 1.4 radii and a wide one at 1.7 radii. Between thermals the whole area sinks by about 0.5 m/s at the peak of the day (0.33 m/s at 11:00), varying by 30 % over a few kilometres. Under cloud streets the sink is weaker, between them stronger.
Clouds and the day
- Cumulus. A cloud forms on top of each active thermal, grows, and decays with it. It marks where the lift is.
- Cloud base. With the default setting it is 1,200 m at 11:00 and 2,000 m at 15:00 above the valley, and higher over high ground.
- Day curve. Thermals are weak in the late morning, peak at 14:00 to 15:00 and fade towards evening. The count follows: 37 thermals in the home valley at 11:00, 60 at 14:00, 44 at 17:00.
- Cloud streets. From 15 km/h of wind thermals start to line up along the wind, and at 25 km/h the streets are fully developed.
- Blue day. No cloud marks the thermals, and they stop at the inversion. You find them by the ground, birds and other gliders.
- Triggers. Thermals start over dry fields and rock (strongest), less over meadows and forest, not over snow or lakes. A slope facing the sun works better, so east faces work in the morning and west faces in the afternoon.
Ridge lift
Wind pushed up by a slope lifts the glider. The lift grows with wind speed and slope steepness and fades with height above the terrain, over a scale of about 350 m. At the Hoher Meissner a 30 km/h westerly gives about 1.5 m/s at 100 m over the west slope, with sink behind the plateau. In the lee the air sinks. Wind along a ridge gives no lift.
Lee waves and rotor
Strong wind across a ridge with stable air above sets up standing waves downwind, locked to the terrain.
- Wavelength. 7.3 km at 50 km/h and 8.7 km at 60 km/h on a Wave day.
- Wind needed. No wave below 25 km/h, full from about 43 km/h.
- Lift. Up to about 4.5 m/s at 3,500 m in the home valley, and about 4.5 m/s at 4,500 m over the Serra del Cadi at La Seu d'Urgell in the Spanish Pyrenees. Over the small Hoher Meissner at the Eschwege gliding site in Hesse, Germany, the wave is weak, at most 1.3 m/s.
- Lenticulars. On a Wave day a lens cloud stands at each strong crest.
- Rotor. Under the crests, from the ground to about crest height, the air tumbles in eddies of 60 to 250 m, with gusts up to a third of the wind speed, whatever the Turbulence setting.
Slope and valley winds
- Up-slope flow. In sunshine air creeps up the slopes in a layer about 120 m deep, up to 2 m/s on a steep slope facing the sun. Right over the slope that is up to about 1 m/s of lift.
- Up-valley wind. From about 11:00, full from 14:00 to 18:00, gone at dusk. It blows in the lowest 200 m of valley floors. At La Seu it is 4 m/s from 210 degrees, up the Segre, so runway 21 is the one in use. A gradient wind of about 29 km/h sweeps it away.
Turbulence
Gusts of 15 to 40 m across make one wing meet different air than the other, so the glider rolls a few degrees on the way into a thermal. Edge eddies sit around each thermal. Turbulence scales with the setting: none when off, 1.5 times as strong on rough.
What is not in yet
Rain, storms, overdevelopment and moving weather zones. The weather does not change during a flight, apart from the day curve, and there is no separate model for wind shadows behind hills beyond the lee sink and the rotor.
Related
- How thermals work, and the lift view that shows this air
- How realistic is it?
- Thermiker vs Condor 3
- Glossary: thermal, ridge lift, wave, rotor, cloud street
- Regions